Once you are ready to wash spray a liberal amount of Bugs N All in a wide enough area to clean by hand or by brush. The key here is to cover the surface so that the bug guts and grime are soaked. 

Wait! This is where people have the most trouble.  Bugs N All is working as long as the surface is wet with Bugs N All solution. So, just be patient and allow Bugs N All to do its job.

How long do I need to wait?

We recommend waiting a minimum of 30 seconds and sometimes up to 2 minutes.   The time needed depends on many factors. But the main factor is the thickness of the splatter or grime. 

We recommend testing a few of the larger splats with a wet towel to see where how complete the releasing process is. Take a wet towel around your finger and gently wipe on the largest bug splat or grime area you can find. If the spot wipes away clean, then horray move to the next step.

You can use whatever washing equipment you normally use to wash your vehicle. For illustration purposes, We'll describe the semi waterless method. Take a dripping wet towel or water-soaked sponge and wipe down the surface, agitating as needed.  

If a second application of Bugs N All is needed, then spot spray and repeat the waiting, testing, and wiping process. 

We recommend rinsing the vehicle even with the semi waterless method.  At a minimum, use a fresh bucket of water and a high absorbent towel to help rinse the vehicle before drying. 

It is possible to skip this step by simply drying the vehicle.  Some streaking is possible if areas are nearly dry already. Simply wet the area with water and wipe dry to eliminate any streaks.

After a good rinse, we recommend drying the vehicle with a soft highly absorbent microfiber towel.  This will help prevent water spots and any possible streaking. While streaking is not common, It can occur if the area was not rinsed shortly after being cleaned and the area had a chance to dry before rinsing.

If streaking does occur, simply rinse the area with a wet towel followed by drying. 

Our goal is to make your job easier. And with bugs n all in your cleaning arsenal, you can experience a high level of success. No more scrubbing like you've done in the past. So get a cold one, sit down and relax. Enjoy the moment!

• In The Shade: So that you get the most out of your Bugs N All, we recommend you apply BNA in a shaded area or where the surface is cool to the touch. It will not harm anything if BNA dries. Simply reactivate it with water. Besides, you only use more BNA when evaporation increases due to surface and ambient temperatures.

• Let It Work: It usually only takes about 20 seconds to release Black Streaks from Aluminum and Fiberglass surfaces. However, it sometimes takes up to 2 minutes for BNA to release Black Streaks.

• Keep It Wet: Keep the area wet until full penetration has occurred.

• Oxidation: Bugs N All will not remove wax. However, If the surface is oxidizing, then there is no wax left on the surface. After cleaning and removing Black Streaks and Oxidation, use a premium wax to help prevent oxidation.

• Black Streaks:  Black Streaks are caused by pollutants in water which leaves deposits on the surface. After it dries it becomes hard. A great way to help prevent Black Streaks is to keep the roof clean.

. 

Cleaning leather is really straight forward. Spray on, let sit for a few seconds and wipe with a clean dry towel. If Bug Splatter is on leather chaps, saddlebags, or coats, spray Bugs N All on and allow it to remain wet for about 30 seconds. Wipe and repeat as needed. A soft brush may be useful with gentle pressure to aid in cleaning and getting into the pores. Refer to the manufacturer's instructions prior to using Bugs N All. However, Bugs N All is safe to use on most leather products. 

• Start Smart: Start by cleaning your aircraft in a well-shaded area or when the sun is not beating down on it. You will get the best results when it is cool to the touch. If Bugs N All drys simply reactivate it with water.

• Using Bugs N All: Spray a liberal amount of Bugs N All on the surface to be cleaned. 

• Time is Your Friend: Allow Bugs N All to work at releasing the Bugs, grease, and grime from your plane. It may take as little as 10 seconds and sometimes up to 2 minutes for BNA to completely release grime. Give it time and you will love how easy it is for you. To test the area, use your finger, by gently rubbing over the soiled spot. Once that spot releases with your finger you can then easily clean the area with a brush and water.

• Cleaning The Interior:  Spray a mist on a towel and wipe down the instrument panel. Spray on seats or other areas and wipe with a dry towel.

We recommend diluting Bugs N All for cleaning the interior windows: add 1/8 cup Ready-To-Use Solution to 1 quart of water into another sprayer. This will eliminate the risk of streaking or smearing on the windows.

• Cleaning Exterior Windows:  Spray a liberal amount of Bugs N All on the exterior windows and allow Bugs N All to completely penetrate grime and bugs. This usually takes 1-2 minutes. Use a sponge with water or whatever method you use to clean the windows. 

• Removing Grease: Spray Bugs N All on and allow time to penetrate. Then wash and rinse normally.

• Start Smart: Start by cleaning your boat in a well-shaded area or when the sun is not beating down on it. You will get the best results when it is cool to the touch. If Bugs N All drys simply reactivate it with water.

• Using Bugs R Gone: The best way we have found to clean is to get a pump-up garden sprayer. Place BNA Ready-to-Use in the garden sprayer, spray a small section, and using a vehicle washing brush and a bucket of plain water, wash, rinse and dry. Depending on how soiled the surface is, you may want to pre-rinse the area before spraying Bugs N All.

• Time is Your Friend: Allow Bugs N All to work at releasing the Bugs, Fish Scales, Water Scum, and grease from your boat. It may take as little as 10 seconds and sometimes up to 2 minutes for BNA to completely release grime. Give it time and you will love how easy it is for you. To test the area, use your finger, by gently rubbing over the soiled spot. Once that spot releases with your finger you can then easily clean the area with a brush and water.

• Cleaning Boat Hull and Bottoms:  Using the Garden sprayer, sprayer a generous amount of Bugs N All on small sections. Wait for about 2 minutes while keeping the area wet with BNA. Use a hard bristle brush, brush the area, and then rinse with water. Repeat as needed.

• Cleaning Vinyl and Carpet: Spray Bugs N All on vinyl and allow time to penetrate. Then use a soft brush and water to wash the area. Repeat as needed. Note: Some older boats may have permanent mildew stains. Bugs N All will help to lighten those stains.

• Cleaning Fishing Equipment: The best way to clean fishing equipment with Bugs N All is to spray BNA on a towel and wipe the equipment off. Remove water spots from windshields and electronic equipment using this method works great.

• Start Smart: Start by cleaning your motor coach in a well-shaded area or when the sun is not beating down on it. You will get the best results when your camper is cool to the touch. If Bugs N All drys simply reactivate it with water.

• Using Bugs N All: The best way we have found to clean the exterior is to get a pump-up garden sprayer. Place BNA Ready-to-Use in the garden sprayer, spray a section in the camper, and using a vehicle washing brush and a bucket of plain water, wash the vehicle, rinse and dry. Depending on how soiled the surface is, you may want to pre-rinse the area before spraying Bugs N All.

• Time is Your Friend: Allow Bugs N All to work at releasing the Bugs, Black Streaks, Oxidation, and Grease from your RV. It may take as little as 10 seconds and sometimes up to 2 minutes for BNA to completely release Bugs. Give it time and you will love how easy it is for you. To test the area, use your finger, by gently rubbing over the soiled spot. Once that spot releases with your finger you can then easily clean the area with a brush and water.

• Cleaning Camper Roofs:  Using the Garden sprayer, sprayer a generous amount of Bugs N All on small sections of the roof. Wait for about 2 minutes. Use a bristle brush to brush the area and then rinse with water. Repeat as needed.  As always, be careful of tripping hazards. 

• Cleaning Awnings:  Pull the awning out and Spray Bugs N All on until it is completely wet. Roll it back up and wait for 10 minutes. Unroll the awning and brush the surface, rinse with water and allow it to dry. Note: Some older awnings may have permanent stains that cannot be removed. 

• Cleaning Vehicle Carpeting: The carpet in your vehicle is rather tough and it takes a lot of abuse over its lifetime. Cleaning this area of the car or truck is pretty straight forward. Spray BNA on the surface and allow a minimum of 10 seconds (and sometimes more than 2 minutes) to work. Use your finger to wipe the area to see how fast BNA is working to determine whether more time is needed before removing the stain. As long as the carpet is wet with BNA, the product is working. In many cases, removing the stain means simply using a towel and wiping the area dry. Other stains may need a more aggressive approach, so consider using a brush to help loosen up the stain. In any case, use common sense. BNA will remove most stains.

• Cleaning Dash Boards: Spray a lite mist of BNA over the dashboard area. Concentrate on cleaning half of the dashboard at a time. Wipe the area cleaning with a dry towel of your choice. If there are heavily soiled areas spot clean or spray a heavy mist on a towel and cover the soiled area with the wet towel for 30 - 60 seconds before wiping.

• Cleaning Window and Mirrors: If streaking occurs while cleaning the interior windows and mirrors, consider diluting BNA by using another sprayer. Dilute the ready to use solution by 1/8 cup per .32 ounces of water. Continue to dilute as needed until no streaking occurs. Here is one important tip. Clean the windows and mirror in a shaded area. The sun evaporates the fluid too quickly, which also contributes to streaking and smearing.

• Cleaning The Seats: Cleaning the seats is similar to cleaning the carpet. Spray on the seat allow about 10 seconds for the product to work before wiping. This method applies to leather, vinyl, fabric seats, booster seats, and car seats.

• In The Shade: So that you get the most out of your Bugs N All, we recommend you apply BNA in a shaded area or where the surface is cool to the touch. It will not harm anything if BNA dries. Simply reactivate it with water. Besides, you only use more BNA when evaporation increases due to surface and ambient temperatures.

• Let It Work: Don't be speedy Gonzales! Bugs N All needs time to break through the grease proteins. Allow a minimum of 10 seconds to 2 minutes to penetration. It may be necessary to use a brush to aid in the penetration and lifting of grease.

• Keep It Wet: Keep the area wet until full penetration has occurred.

• Warm it Up: Bugs N All penetrates grease best in warm temperatures.

• In The Shade: So that you get the most out of your Bugs N All, we recommend you apply BNA in a shaded area or where the surface is cool to the touch. It will not harm anything if BNA dries. Simply reactivate it with water. Besides, you only use more BNA when evaporation increases due to surface and ambient temperatures.

• Let It Work: Allow a minimum of 5 seconds to 2 minutes for full penetration.

• Keep It Wet: Keep the area wet until full penetration has occurred.

• Use Other Tools: It's OK to use Microfibers, Brushes, Blotting Techniques, scrubbing, and so on to cleaning and remove stains. Just use your best judgment and test Bugs N All first on delicate areas where you may not be sure how BNA will handle your cleaning efforts.